Sikafloor® MultiDur EB-12 ECC
Slip resistant broadcast coloured epoxy floor coating system for damp substrates
Sikafloor® MultiDur EB-12 ECC is a 2-part epoxy coloured resin based floor coating system that can provide a hard wearing, seamless, low maintenance, slip resistant gloss finish when broadcast with different aggregate grades on damp substrates. For medium - heavy wear conditions. Thickness 2.0 – 4.0 mm. Internal use.
- Seamless
- Good chemical and mechanical resistance
- Easy application
- Waterproof
- Gloss finish
- Easy cleanability
- Low maintenance
- Good bond to green or hardened damp/dry concrete
System Structure
Usage
- On concrete and cementitious screeds with normal up to medium heavy wear e.g. storage and assembly halls, maintenance workshops, garages and loading ramps.
- On multi-storey and underground car park decks and for wet process areas, e.g. beverage and food industry
Advantages
- Seamless
- Good chemical and mechanical resistance
- Easy application
- Waterproof
- Gloss finish
- Easy cleanability
- Low maintenance
- Good bond to green or hardened damp/dry concrete
Colour
A range of RAL colours are available
Other colours on request.
Appearance
Slip resistant gloss finish
System Details
APPROVALS / STANDARDS
- Refer to individual Product Data Sheet within System Structure
System Structure
Sikafloor® MultiDur EB-12 ECC (~ 2–4 mm)
| Layer | Product |
| 1. Primer | Sikafloor®-80 Epocem Primer |
| 2. Levelling screed | Sikafloor®-81 EpoCem® |
| 3. Seal coat | Sikafloor-150 /151 |
| 4. Wear coat | Sikafloor®-264 N quartz sand 0.3–0.8 mm to excess or Sika® Aggregate-501 |
| 5. Top Coat | Sikafloor®-264 N |
Composition
Epoxy
Nominal thickness
~ 2.0 – 4.0 mm
Abrasion Resistance
| ~35 mg (CS 10/1000/1000) (8 days / +23 °C) | (DIN 53 109 (Taber Abraser Test)) |
Compressive Strength
| 60 MPa ( 28 days at 23 °C / 50 % R.H.) | (EN 13892-2) |
Tensile Strength
| 14 MPa (28 days at 23 °C / 50 % R.H.) | (EN 13892-2) |
Tensile Adhesion Strength
| > 1.5 MPa (failure in concrete) | (ISO 4624) |
Chemical Resistance
Resistant to many chemicals. Contact Sika Technical Service for specific information.
Coefficient of Friction
| μ = 0.54 | (DIN 51131) |
Skid / Slip Resistance
| R11 V4 | (DIN 51130) |
Application
Ambient Air Temperature
+10 °C min / +30 °C max
Relative Air Humidity
80 % r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor temperature must be at least 3 °C above the dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
Can be applied on green or damp concrete, with no standing water.
Although the system can be applied onto green concrete surfaces (> 24 hours), it is advised to allow at least 3 days for early concrete shrinkage to occur in order to prevent shrinkage cracks from appearing on the wearing surface.
Waiting Time / Overcoating
Before applying Sikafloor®-81 EpoCem® on Sikafloor®-80 EpoCem® Primer allow:
| Substrate Temperature | Minimum | Maximum |
| +10 °C | 12 hours | 24 hours |
| +20 °C | 6 hours | 12 hours |
| +30 °C | 4 hours | 6 hours |
Sikafloor®-81 EpoCem® can be overcoated with vapour impermeable coatings when the surface humidity falls below 4%
Not earlier than :
| Substrate Temperature | Waiting Time |
| +10 °C | 2 days |
| +20 °C | 1 day |
| +30 °C | 1 day |
Applied Product Ready for Use
| Temperature | Foot Traffic | Light Traffic | Full Cure |
| +10 °C | ~ 72 hours | ~ 6 days | ~ 10 days |
| +20 °C | ~ 24 hours | ~ 4 days | ~ 7 days |
| +30 °C | ~ 18 hours | ~ 2 days | ~ 5 days |
Note: Times are approximate and will be affected by changing ambient conditions.
Consumption
| Layer | Product | Consumption |
| 1.Primer | 1-2 x Sikafloor®-80 EpoCem®Primer | ~ 0.25–0.4 kg/m2 |
| 2.Levelling screed | Sikafloor®-81 EpoCem® | ~2.25 kg/m2/mm |
| 3.Seal Coat | Sikafloor®-150 / 151 | ~0.4–0.6 kg/m2 |
| 4.Wear Coat | Sikafloor®-264 N | ~0.6-.08 kg/m2 |
| 4.Sand Broadcast | Quartz Sand 0.3-0.8 mm or Sika® Aggregate-501 to excess | ~ 4–6 kg/m2 |
| 5.Top coat/s | 1–2 × Sikafloor®-264 N | ~ 0.6–0.8 kg/m2 |
CLEANING
Refer to the Method Statement Sikafloor®-Cleaning Regime