Sika® Injection-307
Polyacrylic elastic injection resin for permanent watertight sealing
Sika® Injection-307 is a polyacrylic,3-part elastic based injection resin with a very low viscosity and adjustable reaction time
- Provides a passivating environment for embedded steel reinforcement
- Adjustable curing time between 10 and 50 minutes
- Permanently elastic, can absorb limited movements
- Capable of reversibly absorbing (swelling) and releasing (shrinking) moisture
- Very low viscosity comparable to water
- Cured Sika® Injection-307 is insoluble in water and hydrocarbons and resistant to alkalis.
Usage
- Crack and joint injection
- Injection of SikaFuko® injection hoses to seal construction joints
- Sealing water-bearing cracks and voids
- Sealing all types of leaking building components in damp or water saturated ground conditions
- Sealing leaks where there is some minor movement
- Sealing drainage pipe joints, that are, or will be, covered with damp or water saturated soil
- Injection repair of damaged waterproofing membranes (single and double layer systems)
Advantages
- Provides a passivating environment for embedded steel reinforcement
- Adjustable curing time between 10 and 50 minutes
- Permanently elastic, can absorb limited movements
- Capable of reversibly absorbing (swelling) and releasing (shrinking) moisture
- Very low viscosity comparable to water
- Cured Sika® Injection-307 is insoluble in water and hydrocarbons and resistant to alkalis.
Packaging
Ready to use kit:
Part A (Resin) | 2 × 9.6 kg |
Part A1 (Accelerator) | 1 × 1.05 kg |
Part B | 4 × 0.4 kg |
Separate bulk parts:
Part A (Resin) | 1 × 19.2 kg |
Part A1 (Accelerator) | 1 × 5.25 kg |
Part B | 36 × 0.4 kg |
Refer to current price list for packaging variations
Colour
Part A (Resin) | blue – transparent liquid |
Part A1 (Accelerator) | yellow – transparent liquid |
Part B | white - powder |
Product Details
APPROVALS / STANDARDS
-
CE Marking and Declaration of Performance to EN 1504-5 - Concrete injection
-
Watertightness test,EN14068,MPA,Report No.1201/011/16b
-
Corrosion test on steel,EN480-14,RWTH Aachen,Passivation Report No.M2208 and M2378
-
Function test in combination with SikaFuko VT-1 PB-2016-204,Wissbau Essen
- Compatibility tests on PVC/TPO Membranes, EN12637-3, MPA,Report No.1200/554/17
Product Declaration
EN 1504-5:Concrete injection
Chemical Base
3-part polyacrylic resin
Shelf Life
12 months from date of production
Storage Conditions
The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +10 °C and +30 °C. Always refer to packaging.
Density
Part A (Resin) | ~1,073 g/cm3 |
Part A1 (Accelerator) | ~1,040 g/cm3 |
Part B | ~2,100 g/cm3 |
Viscosity
3.8 mPa∙s (complete mixture +20 °C) | (EN ISO 3219) |
Application
Mixing Ratio
Table 1
Accelerator Metering Chart
Ambient Temperature and Accelerator quantity (ml) | |||||
Reaction time | +5 °C (+41 °F) | +15 °C (+59 °F) | +22 °C (+72 °F) | +30 °C | +40 °C (+104 °F) |
10 min | 1170* | 650* | 440 | 360 | 250 |
20 min | 750* | 440 | 340 | 290 | 200 |
30 min | 590* | 390 | 290 | 250 | 170 |
40 min | 550* | 350 | 260 | 230 | 160 |
50 min | 520* | 330 | 230 | 210 | 140 |
* reaction at cold temperatures – more accelerator (A1) is required than is supplied in the kit.
The quantity in Table 1 of accelerator (A1) per 9.6 kg of resin (A), will yield ~20 litres of mixed resin. The total Accelerator solution must always be 1000 ml (refer to example below).
Example
Ambient temperature: +22 °C (+72 °F)
Required reaction time: 30 min.
Accelerator = 290 ml
Water = 710 ml
Total volume = 1000 ml
Note:
1) When using one component pumps: Workability time (pot life) = Factor 0.8 x Reaction time (refer to metering chart)
2) The given data are laboratory parameters and may deviate depending on the situation and conditions on site. Reaction time measured in 100ml specimen.
Ambient Air Temperature
+5 °C min. / +40 °C max.
Substrate Temperature
+5 °C min. / +40 °C max.
Gel time
10–50 minutes
Yield
~ 40 litres per kit
MIXING
Mixing Sequence
1. Hardener solution
Pour 10 litres of water in a clean container. Dissolve the content of 2 bags (total 800 g) of Part B in the water. Stir with a mixer at low speed the hardener solution thoroughly until Part B is completely dissolved.
2. Accelerator solution
Determine the required quantity of accelerator (A1) from the accelerator metering chart (Table 1). Dilute the selected quantity of accelerator with water to a total quantity of 1 litre accelerator solution.
3. Accelerator Solution with Part A resin
Pour the 1 litre of accelerator solution into 1 x 9.6 kg container of Part A and shake/mix thoroughly.
4. Resin solution with hardener solution
Depending on the type of injection pump used activate the injection resin using one of the methods below:
- One component pump: Pour a partial amount of the final pre-mixed solution in the ratio of 1:1 by volume into a clean mixing container. Mix thoroughly and pour into the storage container of the pump.
- Two component pump: Pour the resin solution into the storage container of the pumps ‘A’ side. Pour the Hardener Solution into the storage container of the pumps ‘B’ side. Then pump at a ratio of 1:1 by volume.
CLEANING OF TOOLS
Clean all tools and application equipment in accordance with the Product Data Sheet for the ‘Sika® Injection Cleaning System’.