Product Data Sheet Safety Data Sheet Show all documents
Sikafloor® Level-15

Sikafloor® Level-15

Cementitious self levelling, fast hardening, underlayment for use 0.5 - 15 mm

Sikafloor® Level-15 is a one part, polymer modified, pumpable self levelling fast hardening cementitous underlayment for the levelling and smoothing of interior floors prior to the application of the final floor finish.

  • Fast application because of the good flow and cohesion of the fresh product
  • Easy to place by pump or manual application
  • Capable of levelling surfaces from 0.5 to 15 mm
  • Reduced shrinkage. Good bond and compaction
  • Fast hardening and good drying
  • Good surface hardness
Where to buy
Product Data Sheet Safety Data Sheet Show all documents

Usage

Sikafloor® Level-15 can be applied manually or by pump to level floors at a thickness between 0.5 - 15mm, prior to subsequent finishing with ceramic or stone tiles, linoleum, PVC sheet, wood flooring or carpets etc.
  • Levelling of both large and small surfaces
  • Typical uses are in commercial, residential and domestic properties etc.
  • Provides a suitable substrate for ceramic, stone or vitrified clay tiles, carpets and wood flooring
Sikafloor® Level-15 is compatible with the Sika adhesives used to lay these types of floor finishes.  

Advantages

  • Fast application because of the good flow and cohesion of the fresh product
  • Easy to place by pump or manual application
  • Capable of levelling surfaces from 0.5 to 15 mm
  • Reduced shrinkage. Good bond and compaction
  • Fast hardening and good drying
  • Good surface hardness

Packaging

20 kg bags

Colour

Standard grey powder

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

All values indicated are internal test results according to EN 13892-2 and EN 13892-8. Conforms to the requirements of EN 13813 CT - C25 - F6
Product Information

Chemical Base

Polymer modified Portland cement

Shelf Life

Nine (9) months from date of production if stored as stated.

Storage Conditions

Store properly in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5°C and +30°C.

Bulk Density

1.02 kg/l ± 0.05 (bulk powder)

 
System information

System Structure

Priming:
Prime substrate with Sikafloor®-01 Primer or Sika® Pour on Floor Primer. Can also be primed with Sikafloor®-150 or Sikafloor®-151,fully broadcast with 0.4 - 0.7mm quartz sand. Please refer to the relevant PDS for recommended applications and details.
Levelling:
Place to the required thickness 0.5 - 15mm. Sikafloor® Level-15 is particularly suitable for the subsequent application of floor coverings using products from the Sikabond® elastic bonding range or tiling mortars from the SikaCeram® range.
Technical Information

Compressive Strength

After 24 hours at +20°C

> 15 MPa

After 28 days at +20°C

> 25 MPa

Flexural Strength

After 28 days at +20°C

> 5.0 MPa

Tensile Adhesion Strength

After 28 days at +20°C

> 1.5 MPa

Application

Application Information

Fresh mortar density

1.95 kg/l ± 0.03

Layer Thickness

Minimum: 0.5 mm. Maximum: 15 mm.

Ambient Air Temperature

+8°C min. / +30°C max.

Relative Air Humidity

~ 75% max.

Substrate Temperature

+8°C min. / +30°C max.

Dew Point: Beware of condensation! The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation, blooming or cement laitance on the floor finish.

Pot Life

Approx. 25 minutes (+20°C / 50% R.H.)

The temperature will affect the pot life. Application at temperatures above +20°C will reduce the pot life and the working time. Temperatures below +20°C will increase the pot life and extend the working time.

Waiting Time / Overcoating

Suitable for overcoating after 24 hours in 5mm thickness where 3% (Tramex) substrate moisture content is required. Times are approximate at +23°C and 50% r.h. and will be affected by changing substrate and ambient conditions, particularly the temperature and relative humidity. When overcoating Sikafloor® Level-15 always ensure the moisture content has achieved the required value for the coating product, as the waiting time will vary with application thickness, temperature and ambient humidity. (Refer to the top coat product data sheet.)

Applied Product Ready for Use

Foot traffic

~ 3 hours

Lightly serviceable

~ 24 hours

Fully servicable

~ 7 days

Note: Times are approximate and will be affected by changing substrate and ambient conditions, particularly the temperature and relative humidity.

 
Consumption

Consumption

~ 1.55 ± 0.1 kg of dry powder/m²/mm
This figure is theoretical and does not include for any additional material required due to surface porosity, surface profile, variations in level or wastage, etc.
Application steps

MIXING

Mixing: When mixing manually, place 4.6 – 4.8 litres of cool, clean water into a suitable sized clean vessel. Add a full bag (20 kg) of Sikafloor® Level-15 powder slowly to the water, mixing continuously. Mix thoroughly for a minimum of 3 minutes using a low speed electric stirrer (~ 300 - 400 rpm).

 

APPLICATION

Pump: Use a conventional floor screed dual stage mixer and pump, and control the water dosage to achieve the required flow, measuring the final average flow diameter on a flat, clean, dry flow table.

Cylinder according to EN 12706:2000

Internal diameter: 30mm
Height: 50mm

ASTM C 230-90 / EN 1015-3

Top internal diam: 70mm
Bottom internal diam.: 100mm
Height: 60mm

Flow = 130mm ± 5mm
(4.8 litres per 20 kg)

Flow = 340mm ± 10mm
(4.8 litres per 20 kg)

After placing onto the surface, apply by trowel or pin screed rake to the required thickness. Roll thoroughly with a spiked roller in two directions to remove any entrapped air.
Manual:
Pour the mixed material onto the primed surface and apply by trowel or pin screed rake to the required thickness. Roll thoroughly with a spiked roller in two directions to remove any entrapped air.

CLEANING OF TOOLS

Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be removed mechanically.

Documents