Product Data Sheet Safety Data Sheet Show all documents
Sikasil® NG
Sikasil® NG
Sikasil® NG
Sikasil® NG
Sikasil® NG
Sikasil® NG
Sikasil® NG
Sikasil® NG

Sikasil® NG

Specialist grade silicone sealant with superior mould resistance and unique adhesion to bathroom acrylic plastics

Sikasil® NG is a neutral cure, silicone sealant which provides a permanent watertight seal to various substrates including acrylic plastics, ceramics, and some powder coated surfaces. Sikasil® NG exceeds the 15 year minimum requirements of the durability provisions of the New Zealand Building Regulations 1992 Clause B2 providing:

  • It is used in strict accordance with the manufacturer’s recommendations’.
  • It is used with the design parameters stated in this data sheet.
  • It is used in conjunction with other approved building systems and materials.
Durability covers weathering and adhesion characteristics. For conditions outside those stated in this data sheet, contact Sika’s Technical Service Department.  

  • Excellent adhesion to acrylic, ABS and polycarbonate plastics
  • Recommended for use with Hardiglaze, Duracryl, Clearlite Showers, Athena Showers, Kohler and Seratone and many other panels
  • Remains flexible at low (-40°C) and high (+150°C) temperatures
  • U.V. resistant
  • Fast cure
  • Low shrinkage during cure
  • Also suitable for glass, metals, coated/painted metals, and timber
Where to buy
Product Data Sheet Safety Data Sheet Show all documents

Usage

Sikasil® NG has been specifically formulated for use as a joint sealant between acrylic plastic shower, bath and basin units and adjacent building components. Sikasil® NG is also suitable for general purpose sealing to and between a wide range of plastics.

Advantages

  • Excellent adhesion to acrylic, ABS and polycarbonate plastics
  • Recommended for use with Hardiglaze, Duracryl, Clearlite Showers, Athena Showers, Kohler and Seratone and many other panels
  • Remains flexible at low (-40°C) and high (+150°C) temperatures
  • U.V. resistant
  • Fast cure
  • Low shrinkage during cure
  • Also suitable for glass, metals, coated/painted metals, and timber

Packaging

300 ml cartridge, box of 12

Colour

Arctic White, Translucent

Product Details

Product Information

Shelf Life

Twelve (12) months when stored as stated.

Storage Conditions

Store in original unopened packaging in cool, dry conditions.

Density

~ 1.01 g/cm³
Technical Information

Shore A Hardness

20

(CQP 023-1)

Tensile Strength

~ 1.3 N/mm²

(Standard)

Elongation

100% modulus: ~ 0.3 N/mm²

(CQP 036-1)

Movement Capability

Butt joints ±25%. Lap joints ±50%

Chemical Resistance

Resistant to weak acids and alkalis, soaps and detergent. Not resistant to petrol and aggressive solvents.

Joint Design

Min. joint size: 5mm x 5mm. Max. joint size: 25mm wide x 10mm deep.

Application

Application Information

Skin Time

20 minutes

Tack Free Time

120 minutes

 
Consumption

Yield

On average one 300ml cartridge will supply 15 m of 5mm sealant bead.
Application steps

SUBSTRATE PREPARATION

Joint surfaces must be clean, dry and free from frost. Remove all dirt, laitance, loose material, mould release and curing agents, and foreign matter. In all joints a bond breaker must be used to prevent sealant contact with the back of the joint, and hence allow optimum performance. In shallow joints self-adhesive polyethylene tape can be used. Deep joints should incorporate a backing strip such as Sika PEF Rod to support the sealant while also acting as a bond breaker. For a neat finish mask the areas adjacent to the joint.

 

PRIMING: On most surfaces sealant adhesion will be improved by the use of a primer. In applications where adhesion is critical (e.g. high
movement joints) a primer is highly recommended. For glass, ceramics and mill finished aluminium no priming is required. For powder coated
aluminium, priming requirements will vary and an adhesion test will need to be carried out. For timber and other porous surfaces use Sika® Primer-3 N. Most plastics do not require a primer although an adhesion test is recommended prior to application.

CLEANING OF TOOLS

Clean tools immediately after use with Sika® Remover-208.

Documents